5113 Low Noise Voltage Preamplifier

Model 5113 Low Noise Voltage Preamplifier

The model 5113 is a high performance, low noise voltage preamplifier with continuously adjustable gain and selectable high, low or bandpass filtering. Its input can be configured for either single-ended or true differential operation with either DC or AC coupling, and its output will deliver up to 1 V pk-pk into a 50 Ω load.

All the principal instrument controls are operated via the three front-panel rotary knobswith a back-lit LCD display to show their present settings. The instrument also includesan optically isolated bi-directional RS232 interface allowing remote operation and interrogation of all controls. Since in some experiments even the very low levels of noise introduced by the internal microprocessor that supports these capabilities may cause problems, the unit includes a "sleep" function whereby every source of digital noise is turned off after a predetermined interval. When in the sleep mode the preamplifier "wakes up" as soon as any control is adjusted and goes back to sleep when adjustment is complete.

The instrument can either be continuously line-powered from the model PS0108 power supply supplied with it, or be run from the internal rechargeable batteries which are charged whenever the power supply is connected. Battery operation often allows troublesome line frequency pick-up to be eliminated, as well as permitting operation away from a source of line power.

If the signal of interest is limited to a single frequency or narrow range of frequencies then the filters allow selective signal amplification, making subsequent signal measurement, for example on an oscilloscope or a lockin amplifier, easier. The filters can of course be switched out of use to give a flat frequency response.

The model 5113 will be of use in applications as diverse s radio astronomy, audiometry, test and measurment, process control and general purpose signal amplification as well as being ideally suited to work with our range of lock-in amplifiers.
  • Documents +

  • Specifications +


    General
    DC or AC coupled voltage amplifier with adjustable gain and a maximum freguency response extending from DC to 1 MHz. Single-ended or differential high-impedance input, and single-ended output, via BNC connectors.

    Signal channel high and low pass filters with variable cut-off frequencies and slope may be switched into circuit to give an overall low-pass, high-pass, bandpass or flat response.

    Computer control via optically isolated RS232 interface.

    Battery powered from internal rechargeable batteries, which recharge when separate line power supply is connected.
    Inputs
    Modes A or A-B
    Coupling AC or DC
    Impedance
    AC coupled
    DC coupled

    either 10 MΩ or 100 MΩ in parallel with 25 pF and in series with 0.1 µF
    either 10 MΩ or 100 MΩ in paralled with 25 pF
    Max input without Damage
    DC coupled
    AC coupled


    + 10 V, -9 V
    Coupling capacitors can withstand 100 V. Transients that pass through coupling capacitors must not exceed DC coupled operation limiits
    Max input for Linear Operation
    Common mode
    Differential mode

    1 V peak.
    See Table 1
    Common Mode Rejection Ratio, CM.R.R.
    DC to 1 kHz
    1 kHz to 1 MHz



    >120 dB
    -6 dB/octave
    Gain Coarse gain of x5 to x50,000 in 1-2-5 sequence with an accuracy of 1%. Fine gain extends range from x1 to x100,000 with an accuracy of 2%. An uncalibrated vemier provides gain adjustment of +20% of coarse gain
    Overload Recovery Front-panel push button or computer command
    Voltage Noise Typically 4 nV/√Hz at 1 kHz referred to input - see also noise contours on page 11
    Filters
    Type One high-pass and one low-pass stage
    Mode Low-pass, High-pass, Bandpass, Flat (No filter)
    Slope
    Low pass
    High pass
    Bandpass

    6 or 12 dB/octave
    6 or 12 dB/octave
    6 dB/octave
    Frequency Response
    Flat Mode
    Low-pass

    High-pass


    DC to 1 MHz.
    -3 dB frequency selectable from 0.03 Hz to 300 kHz in a 1-3-10 sequence (Figure 1)
    -3 dB frequency selectable from 0.03 Hz to 300 kHz in a 1-3-10 sequence (Figure 2)
    DC Drift
    Referred to Input (DC coupling) Maximum 10µ/º or less than 10 µV/º c or less than 10µV per 24 hours at constant ambient temperature
    Referred to Output (AC coupling)
    Course gain only
    With Fine Gain
    75 µV/º C
    250 µv/º C maximum
    DC Input Offset Control
    Front-panel screwdriver control provides for DC zeroing
    Output
    Max Output Voltage 2 V pk-pk ahead of 50 Ω
    Output imipedance 50 Ω ± 2 %
    Computer Interface
    Type Opto-isolated RS232
    Connector DB25 25-pin female connector
    Baud Rate 300 to 9600 baud
    Parameters No parity, eight data bits and one stop bit
  • Options +


    Item Model Number
    Rack Mount K0304
    Pack of 20 Alkaline Batteries PS0109
    Power Cable-
    Utilizes power from Lock-in Amplifier
    C0218
  • Software +


    Item Model Number
    Acquire Software
    The software includes a powerful plotting engine that lets you show data just as you want it using a variety of line styles, allows data export to both text and CSV files, offers comprehensive clipboard support, and includes a context-sensitive help system
    Acquire
    Active X Control SRINSTCOMMS